Arkadaşlar selam ; aşağıdaki kodu lpc2138 ile yapmaya çalışıcam ama takıldım.
#define DATA P1_1 //p1_1 yeri pisel'i mi tanıtmam gerekiyor ? 2368 hangi ayağını sda olarak kullanıcaksam
#define SCK P1_0
if (i & value) DATA=1; //burada o pini 1 'mi yapmam gerekiyor ?
konu hakkında yardımlarınızı bekliyorumç
/***********************************************************************************
Project: SHT1x/7x demo program (V2.4)
Filename: SHT1x_sample_code.c
Prozessor: 80C51 family
Compiler: Keil Version 6.23a
Autor: MST
Copyrigth: (c) Sensirion AG
***********************************************************************************/
// Revisions:
// V2.4 calc_sht11() Coefficients for humidity and temperature conversion
// changed (for V4 sensors)
// calc_dewpoint() New formula for dew point calculation
#include <AT89s53.h> //Microcontroller specific library, e.g. port definitions
#include <intrins.h> //Keil library (is used for _nop()_ operation)
#include <math.h> //Keil library
#include <stdio.h> //Keil library
typedef union
{ unsigned int i;
float f;
} value;
//----------------------------------------------------------------------------------
// modul-var
//----------------------------------------------------------------------------------
enum {TEMP,HUMI};
#define DATA P1_1
#define SCK P1_0
#define noACK 0
#define ACK 1
//adr command r/w
#define STATUS_REG_W 0x06 //000 0011 0
#define STATUS_REG_R 0x07 //000 0011 1
#define MEASURE_TEMP 0x03 //000 0001 1
#define MEASURE_HUMI 0x05 //000 0010 1
#define RESET 0x1e //000 1111 0
//----------------------------------------------------------------------------------
char s_write_byte(unsigned char value)
//----------------------------------------------------------------------------------
// writes a byte on the Sensibus and checks the acknowledge
{
unsigned char i,error=0;
for (i=0x80;i>0;i/=2) //shift bit for masking
{ if (i & value) DATA=1; //masking value with i , write to SENSI-BUS
else DATA=0;
_nop_(); //observe setup time
SCK=1; //clk for SENSI-BUS
_nop_();_nop_();_nop_(); //pulswith approx. 5 us
SCK=0;
_nop_(); //observe hold time
}
DATA=1; //release DATA-line
_nop_(); //observe setup time
SCK=1; //clk #9 for ack
error=DATA; //check ack (DATA will be pulled down by SHT11)
SCK=0;
return error; //error=1 in case of no acknowledge
}
//----------------------------------------------------------------------------------
char s_read_byte(unsigned char ack)
//----------------------------------------------------------------------------------
// reads a byte form the Sensibus and gives an acknowledge in case of "ack=1"
{
unsigned char i,val=0;
DATA=1; //release DATA-line
for (i=0x80;i>0;i/=2) //shift bit for masking
{ SCK=1; //clk for SENSI-BUS
if (DATA) val=(val | i); //read bit
SCK=0;
}
DATA=!ack; //in case of "ack==1" pull down DATA-Line
_nop_(); //observe setup time
SCK=1; //clk #9 for ack
_nop_();_nop_();_nop_(); //pulswith approx. 5 us
SCK=0;
_nop_(); //observe hold time
DATA=1; //release DATA-line
return val;
}
//----------------------------------------------------------------------------------
void s_transstart(void)
//----------------------------------------------------------------------------------
// generates a transmission start
// _____ ________
// DATA: |_______|
// ___ ___
// SCK : ___| |___| |______
{
DATA=1; SCK=0; //Initial state
_nop_();
SCK=1;
_nop_();
DATA=0;
_nop_();
SCK=0;
_nop_();_nop_();_nop_();
SCK=1;
_nop_();
DATA=1;
_nop_();
SCK=0;
}
//----------------------------------------------------------------------------------
void s_connectionreset(void)
//----------------------------------------------------------------------------------
// communication reset: DATA-line=1 and at least 9 SCK cycles followed by transstart
// _____________________________________________________ ________
// DATA: |_______|
// _ _ _ _ _ _ _ _ _ ___ ___
// SCK : __| |__| |__| |__| |__| |__| |__| |__| |__| |______| |___| |______
{
unsigned char i;
DATA=1; SCK=0; //Initial state
for(i=0;i<9;i++) //9 SCK cycles
{ SCK=1;
SCK=0;
}
s_transstart(); //transmission start
}
//----------------------------------------------------------------------------------
char s_softreset(void)
//----------------------------------------------------------------------------------
// resets the sensor by a softreset
{
unsigned char error=0;
s_connectionreset(); //reset communication
error+=s_write_byte(RESET); //send RESET-command to sensor
return error; //error=1 in case of no response form the sensor
}
//----------------------------------------------------------------------------------
char s_read_statusreg(unsigned char *p_value, unsigned char *p_checksum)
//----------------------------------------------------------------------------------
// reads the status register with checksum (8-bit)
{
unsigned char error=0;
s_transstart(); //transmission start
error=s_write_byte(STATUS_REG_R); //send command to sensor
*p_value=s_read_byte(ACK); //read status register (8-bit)
*p_checksum=s_read_byte(noACK); //read checksum (8-bit)
return error; //error=1 in case of no response form the sensor
}
//----------------------------------------------------------------------------------
char s_write_statusreg(unsigned char *p_value)
//----------------------------------------------------------------------------------
// writes the status register with checksum (8-bit)
{
unsigned char error=0;
s_transstart(); //transmission start
error+=s_write_byte(STATUS_REG_W);//send command to sensor
error+=s_write_byte(*p_value); //send value of status register
return error; //error>=1 in case of no response form the sensor
}
//----------------------------------------------------------------------------------
char s_measure(unsigned char *p_value, unsigned char *p_checksum, unsigned char mode)
//----------------------------------------------------------------------------------
// makes a measurement (humidity/temperature) with checksum
{
unsigned char error=0;
unsigned int i;
s_transstart(); //transmission start
switch(mode){ //send command to sensor
case TEMP : error+=s_write_byte(MEASURE_TEMP); break;
case HUMI : error+=s_write_byte(MEASURE_HUMI); break;
default : break;
}
for (i=0;i<65535;i++) if(DATA==0) break; //wait until sensor has finished the measurement
if(DATA) error+=1; // or timeout (~2 sec.) is reached
*(p_value) =s_read_byte(ACK); //read the first byte (MSB)
*(p_value+1)=s_read_byte(ACK); //read the second byte (LSB)
*p_checksum =s_read_byte(noACK); //read checksum
return error;
}
//----------------------------------------------------------------------------------
void init_uart()
//----------------------------------------------------------------------------------
//9600 bps @ 11.059 MHz
{SCON = 0x52;
TMOD = 0x20;
TCON = 0x69;
TH1 = 0xfd;
}
//----------------------------------------------------------------------------------------
void calc_sth11(float *p_humidity ,float *p_temperature)
//----------------------------------------------------------------------------------------
// calculates temperature [°C] and humidity [%RH]
// input : humi [Ticks] (12 bit)
// temp [Ticks] (14 bit)
// output: humi [%RH]
// temp [°C]
{ const float C1=-2.0468; // for 12 Bit RH
const float C2=+0.0367; // for 12 Bit RH
const float C3=-0.0000015955; // for 12 Bit RH
const float T1=+0.01; // for 12 Bit RH
const float T2=+0.00008; // for 12 Bit RH
float rh=*p_humidity; // rh: Humidity [Ticks] 12 Bit
float t=*p_temperature; // t: Temperature [Ticks] 14 Bit
float rh_lin; // rh_lin: Humidity linear
float rh_true; // rh_true: Temperature compensated humidity
float t_C; // t_C : Temperature [°C]
t_C=t*0.01 - 40.1; //calc. temperature [°C] from 14 bit temp. ticks @ 5V
rh_lin=C3*rh*rh + C2*rh + C1; //calc. humidity from ticks to [%RH]
rh_true=(t_C-25)*(T1+T2*rh)+rh_lin; //calc. temperature compensated humidity [%RH]
if(rh_true>100)rh_true=100; //cut if the value is outside of
if(rh_true<0.1)rh_true=0.1; //the physical possible range
*p_temperature=t_C; //return temperature [°C]
*p_humidity=rh_true; //return humidity[%RH]
}
//--------------------------------------------------------------------
float calc_dewpoint(float h,float t)
//--------------------------------------------------------------------
// calculates dew point
// input: humidity [%RH], temperature [°C]
// output: dew point [°C]
{ float k,dew_point ;
k = (log10(h)-2)/0.4343 + (17.62*t)/(243.12+t);
dew_point = 243.12*k/(17.62-k);
return dew_point;
}
//----------------------------------------------------------------------------------
void main()
//----------------------------------------------------------------------------------
// sample program that shows how to use SHT11 functions
// 1. connection reset
// 2. measure humidity [ticks](12 bit) and temperature [ticks](14 bit)
// 3. calculate humidity [%RH] and temperature [°C]
// 4. calculate dew point [°C]
// 5. print temperature, humidity, dew point
{ value humi_val,temp_val;
float dew_point;
unsigned char error,checksum;
unsigned int i;
init_uart();
s_connectionreset();
while(1)
{ error=0;
error+=s_measure((unsigned char*) &humi_val.i,&checksum,HUMI); //measure humidity
error+=s_measure((unsigned char*) &temp_val.i,&checksum,TEMP); //measure temperature
if(error!=0) s_connectionreset(); //in case of an error: connection reset
else
{ humi_val.f=(float)humi_val.i; //converts integer to float
temp_val.f=(float)temp_val.i; //converts integer to float
calc_sth11(&humi_val.f,&temp_val.f); //calculate humidity, temperature
dew_point=calc_dewpoint(humi_val.f,temp_val.f); //calculate dew point
printf("temp:%5.1fC humi:%5.1f%% dew point:%5.1fC\n",temp_val.f,humi_val.f,dew_point);
}
//----------wait approx. 0.8s to avoid heating up SHTxx------------------------------
for (i=0;i<40000;i++); //(be sure that the compiler doesn't eliminate this line!)
//-----------------------------------------------------------------------------------
}
}
SHT 11 sensör tam I2C sayılmaz kendine has fonksiyonlar türetmişler o yüzden manual olarak yazacağız ben sizin için aşağıda bir örnek çalıştırdım yalnız cortex m3 de lcd ye gönderirken kullandığım sprintf fonksiyonu lpc2138 de çalışmadı int olarak düzenlemek zorunda kaldım biraz araştırma yaparsanız belki siz çözersiniz.
Kolay gelsin.
(http://img232.imageshack.us/img232/1571/xfi.png)
http://hotfile.com/dl/113184516/ebbb196/SHT11LPC2138.rar.html
Çok teşekkür ederim tam istediğimdi. sht11.h ve sht11.c dosyasını sizmi yazdınız ?
1 ay kadar önce ben düzenledim yukarıda paylaştığınız koduda incelemiştim farklı kaynakların birleşimi sayılır.
arm7 de float değeri lcd ye yazdıramadığım için sprintf ile float değer dönüşümlü çalışmıyor bu konu hakkında bişeyler geliştirirseniz burada paylaşınız.
Tekrar çok teşekkür ederim. Şimdi sizin gönderdiğiniz kodla sht'nin sitesinden indirdiğim kodu kontrol edicem.